Efficient Layouts: All Rotor & Stator Recipes (2024)

These layouts are all correct as of Update 6.

Check out the video here:
EfficientAlternate Rotor & StatorRecipes Satisfactory Update 6.

The vanilla recipe,requires 90 Iron ore per minute and produces 8 Statorsper minute.

First place three smelters at the start of your build producing iron ingots each at 100% efficiency. Each of these smelters should then split their ingots betweentwo constructorsand all 6 of these constructors should be set to iron rods.

At this point we need to split the 90 iron rods between two lines, one holding 40 iron rods, the second holding 50. To do this place a splitter infront of the third constructor and run two outputs to the left side leading to the first two constructors merging line, and then the third splitter output should merge with the merging line of the three constructors to the left of it.

Next, run the 50 iron rods line to five constructors, these should each be set to screws and merged into two equal lines and sent on to two assemblers. In the photos attached the mergers are connected to an elevator which transports the screws beneath the build and across to the assemblers. (green boxes)

The 40 iron rods that are left over from the first set of constructors should be sent to the two assemblers and split evenly between the two, these assemblers will be set to rotors, producing 8 rotors per minute at 100% clockspeed.

Do not that the screw lines will need to be mk2 as 100 items will be travelling along each of the lines.

The next layout is for Copper Rotors, in this layoutwe will be using the Steel Screwalternate recipe as well as overclocking a single foundry. This particular layout requireslayout only requires 60 coal, 60 iron ore and 180 copper ore, and produces 45 rotors per minute.

First place a foundry and overclock it to 133.33% clockspeed (alternatively place 2 foundries and set each to 66.66% clockspeed) This will take the iron and the coal and turn it into 60 steel ingots per minute. These will be sent on to be steel beams in a single constructor before being fed into three more constructors producing steel screws each at 100% clockspeed, these can be merged together if using a mk5 belt and will be sent on to the four assemblers set to copper rotors with each running at 100% clockspeed.

Next send the 180 copper ore to six smelters, these will send the 180 copper ingots along to a manifold of 9 constructors producing copper sheets at 100% clockspeed before being sent on to the 4 assemblers, which will now be producing 45 copper rotors per minute.

The next layout is for Steel Rotors, for this we will need 120 coal per minute, along with 120 iron ore and 120 copper ore. These resources will go on to produce 40 steel rotors per minute.

First we will need three foundries, two will be set to 100% clockspeed as well as a third foundry set to 66.7% clockspeed. These will produce steel ingots which will be sent on to four constructors each producing steel pipes at 100% clockspeed and running these pipes up to the manifold of 8 assemblers.

Next we will take the copper ore to four smelters, each producing copper ingots at 100% clockspeed and then splitting the ingots each between two constructors. All eight of these constructors will be set to wire. The wire will then be sent along to the eight assemblers which will be set to steel rotors and each run at 100% clockspeed, producing a total of 40 rotors per minute.

The next layout is for stators, and is also the reason why I love steel rotors. Both the steel rotors and stators are produced with the same ingredients meaning a motor factory will only need to import coal, iron and copper ore. This particular layout will produce 40 stators (you'll thank me later when you merge the rotors and stators together to produce motors)
For this layout you will need 180 coal, 180 iron ore and 160 copper ore. These will be used to produce a total of 40 vanillastators.

First, run the coal and the iron ore to four foundries, these should each be running at 100% clockspeed producing steel ingots. These ingots will then be merged and run along a manifold to six constructors producing steel pipes. These steel pipes will then run along to the eight assemblers that produce stators for this build.

Our final layout is for quickwire stators. For this build we will require 120 coal, 120 Iron ore and 180 caterium ore to produce a total of 40 quickwire stators.

First place three foundries down, the first two will run at 100% clockspeed producing steel ingots and the third foundry will run at 66.667% clockspeed. All steel ingots will run along a manifold of four constructors, each set to steel pipes. These will then be sent on to five assemblers, all of which will produce quickwire stators.

Next place four smelters that produce caterium ingots, each will be set to 100% clockspeed before running along a manifold to five constructors. Each constructor will be set to quickwire and will output their 60 quickwire perminute, each to an independant assembler. (alternatively if you have mk4 belts you can run these along a manifold)

These assemblers will each produce quickwire stators at 100% clockspeed totalling 40 stators per minute.